The only energy required is provided by compressed air.^[1] This air is usually compressed by a compressor or a blower. The air is injected in the lower part of a pipe that transports a liquid. By buoyancy the air, which has a lower density than the liquid, rises quickly. By fluid pressure, the liquid is taken in the ascendant air flow and moves in the same direction as the air. The calculation of the volume flow of the liquid is possible thanks to the physics of two-phase flow.

• Airlift pumps are often used in deep dirty wells where sand would quickly abrade mechanical parts. (The compressor is on the surface and no mechanical parts are needed in the well). However airlift wells must be much deeper than the water table to allow for submergence. Air is generally pumped at least as deep under the water as the water is to be lifted. (If the water table is 50 ft below, the air should be pumped 100 feet deep). It is also sometimes used in part of the process on a wastewater treatment plant if a small head is required (typically around 1 foot head).
• Airlifts are used to collect fauna samples from sediment.^[2] Airlifts can oversample zooplankton and meiofauna but undersample animals that exhibit an escape response.^[2]
• In an aquarium an airlift pump is sometimes used to pump water to a filter.
• In a coffee percolator the airlift principle is used to circulate the coffee.

The first airlift pump is considered to be invented by the German engineer Carl Emanuel Löscher [de] in 1797.

Advantages edit

• The pump is very reliable. The very simple principle is a clear advantage. Only air with a higher pressure than the liquid is required.
• The liquid is not in contact with any mechanical elements. Therefore, neither the pump can be abraded (which is important for sandwater wells), nor the contents in the pipe (which is important for archeological research in the sea).
• Act as a water aerator and can in some configurations lift stagnant bottom water to the surface (of water tanks).
• Since there are no restrictive pump parts, solids up to 70% of the pipe diameter can be reliably pumped.

Disadvantages edit

• Cost: while in some specific cases the operational cost can be manageable, most of the time the quantity of compressed air, and thus the energy required, is high compared to the liquid flow produced.^[3][4]
• Conventional airlift pumps have a flow rate that is very limited. The pump is either on or off. It is very difficult to get a wide range of proportional flow control by varying the volume of compressed air. This is a dramatic disadvantage in some parts of a small wastewater treatment plant, such as the aerator.^[5]
• the suction is limited.
• this pumping system is suitable only if the head is relatively low. If one wants to obtain a high head, one has to choose a conventional pumping system.
• because of the principle, air (oxygen) dissolves in the liquid. In certain cases, this can be problematic, as, for example, in a waste water treatment plant, before an anaerobic basin.

Design improvements edit

A recent (2007) variant called the "geyser pump" can pump with greater suction and less air. It also pumps proportionally to the air flow, permitting use in processes that require varying controlled flows. It arranges to store up the air, and release it in large bubbles that seal to the lift pipe, raising slugs of fluid.^[6]

• Airlift (dredging device) – Dredging device using injected air to move water and entrained load up a pipe
• Gas lift – Raising a fluid by introducing bubbles of gas into the outlet tube
• Pipe network analysis
• Pulser pump
• Water eductor – Type of pump used in archeology

• "Airlift calculation by Sanitaire (pdf document)" (PDF). sanitaire.com. 2012-01-05. Archived from the original on 2012-01-05. Retrieved 2022-06-25.{{cite web}}: CS1 maint: unfit URL (link)
• Recovered airlift_basic_calculation.xls via Waybackmachine. Mirrored at filedropper dot com /airliftbasiccalculation.